threads
Page 2 of 2
Ask A Pro \  How Much To Shorten A Rear End To Lay Doors On 24s And Not Rub?!?

How Much To Shorten A Rear End To Lay Doors On 24s And Not Rub?!?

Ask A Pro Q & A
views 1142
replies 18
following 11
 
IMDORED   +1y
Originally posted by SuicidalCustomz



Originally posted by KNDAlow



4 inches, check out this guys profile, hes on 22s though...

Http://www.streetsourcemag.com/Profile.aspx?ProfileID=28858

thanks for the info bro yea i seen your doored truck at freak show looks kool im planning on having mine cruizin maybe by blooddrag 08 or atleast spring fling 08! are u bringin yours to any of those shows?



not sure if we will be there or not, im building a house and shop right now, so the truck is on hold for awhile until its finished. if we get the truck finished early enough in the spring im sure we will be making some appearances. by the way, my wheels are a +50
SuicidalCustomz   +1y
ok sounds good vamos, thanks everyone for the info once i get the rear shorten and wheels on the truck i will be sure to make a profile for my doored truck.
SuicidalCustomz   +1y
yes that truck is pretty much badazz i sent him a message asking how short he shorten his rear and what his offset was on his wheels so maybe he will email me back.
KNDAlow   +1y
Originally posted by BOYETT



This guy is doored on 24s...

http://streetsource.com/viewownerprofile.aspx?profileid=37014

ya that truck is badass, i was lookin for that one but couldnt find it.
bdroppeddak   +1y
the best bet is to figure out what kind of wheel width you want, and what kind of lip you want on the wheel to figure up what backspacing you will need, then get them, then do some measuring..... what i have done in the past is with the fender wells cut out of the bed, i measure the distance between the bedside, then subtract about 3/4-1 inch from the highest point that the tire will go, then i take the wheel width x 2 + 2" (wheels are usually 1" wider than the width listed) and subtract the backspacing x2, then i get the track width needed to tuck.....
SuicidalCustomz   +1y
Originally posted by bdroppeddak



the best bet is to figure out what kind of wheel width you want, and what kind of lip you want on the wheel to figure up what backspacing you will need, then get them, then do some measuring..... what i have done in the past is with the fender wells cut out of the bed, i measure the distance between the bedside, then subtract about 3/4-1 inch from the highest point that the tire will go, then i take the wheel width x 2 + 2" (wheels are usually 1" wider than the width listed) and subtract the backspacing x2, then i get the track width needed to tuck.....

oh yea dude that sounds like it will work i didnt think about doing it like that...yea i will try that thanks for the info bro

dragginrkr   +1y
when you figure out how much you want it narrowed and you need someone to do it let me know dragginbyu@hotmail.com i had my fullsize at freakshow and will be there with it again next year
SuicidalCustomz   +1y
Originally posted by dragginrkr



when you figure out how much you want it narrowed and you need someone to do it let me know dragginbyu@hotmail.com i had my fullsize at freakshow and will be there with it again next year

yea i seen your truck at freak show and southeast showdown i think yall just shot primer on it before southest showdown when i walked by it u could still smell the paint..lol but anyways how much do ya charge to shorten the rear i might sent it up to ya and let you do it once i figure out how short i want it.