mopar978
+1y
--------------------------------------------
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
mopar978
+1y
A little bit of a clearance problem. Caused for a trip the parts store.
Finally got our brakes in. And they sure look nice.
Finally got our brakes in. And they sure look nice.
DeepSouthS10
+1y
--------------------------------------------
AutoRodTechnologies said:
--------------------------------------------
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
--------------------------------------------
I knew I asked about a rear end and I couldnt remember what thread it was in lol. Glad I finally found it. Thats awesome, sounds like something I may need to look into. Are you getting axels from Moser?
BTW, those brakes look bad ass!
AutoRodTechnologies said:
--------------------------------------------
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
--------------------------------------------
I knew I asked about a rear end and I couldnt remember what thread it was in lol. Glad I finally found it. Thats awesome, sounds like something I may need to look into. Are you getting axels from Moser?
BTW, those brakes look bad ass!
mopar978
+1y
--------------------------------------------
DeepSouthS10 said:
--------------------------------------------
AutoRodTechnologies said:
--------------------------------------------
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
--------------------------------------------
I knew I asked about a rear end and I couldnt remember what thread it was in lol. Glad I finally found it. Thats awesome, sounds like something I may need to look into. Are you getting axels from Moser?
BTW, those brakes look bad ass!
--------------------------------------------
Probably going to get a set we have shortened and re-splined.
DeepSouthS10 said:
--------------------------------------------
AutoRodTechnologies said:
--------------------------------------------
DeepSouthS10 said:
awesome project. where do you get an axel housing like that?
--------------------------------------------
It's basically a new 9", but we are getting the axle set up to match the bolt pattern that we are going to be using on the front also.
When you buy these they come as 3 pieces and have to be welded together. the center, and then the tubes.then you need to set up and shorten it to length, and weld the ends on and then get shafts cut to length or buy new ones.By doing it this way you pretty much get everything set up as you want. The right bolt pattern, set up for the brakes we want, and the right width.
We got this one from lane automotive.
--------------------------------------------
I knew I asked about a rear end and I couldnt remember what thread it was in lol. Glad I finally found it. Thats awesome, sounds like something I may need to look into. Are you getting axels from Moser?
BTW, those brakes look bad ass!
--------------------------------------------
Probably going to get a set we have shortened and re-splined.
