threads
Page 28 of 33
Mazda Projects \  1990 Mazda B2200 Is BodyDropped!!!

1990 Mazda B2200 Is BodyDropped!!!

Mazda Projects
views 80667
replies 326
following 49
 
mazdadropped   +1y
I haven't rebuilt it yet lmao the front still needs reinforcing oviously
the firewall needs to be out a little more and it will be shaved
The bodydrops almost complete then shaving the backwall also then ill start the new backhalf

That's mostly rebuilt and no it hasn't started not sure what u guys don't understand but if I hear it needs to be rebuilt you guys seriously are really gay like todds new thread says
fitbmx180   +1y
show us pics and prove us wrong..
toddluck   +1y
Well im done giving advice or anymore input....we are not picking on you ......but what ever
dropped90(justin)   +1y
It needs to be rebuilt......and yes todd you are gay.









-Justin
mazdadropped   +1y
Well its been a while since this has been updated , to be honest not a whole lot has been changed , i brought it home its been sitting in my driveway since august because i lost my job, still havent found one.


I sanded the frame in my engine bay, my control arms. i cut the 1/4" plate flush with the top of the upper control arm mounts so my steering column will turn without rubbing on it. made the ECU wiring harness and vacuum lines tucked under the carb. cut my fire wall out and lots of other small details. Heres some pics.

Oh one more thing. i DID NOT say that the control arms or upper bag brackets have gussets yet or the frame was torn apart yet becuase that will be done when it goes to lances place this winter


Front end test fit
thread post photo


Straightened the floor after firewall was cut out
thread post photo


Teaser of the Control arms sanded down
thread post photo


Can anyone tell me whats on the carb? its from the drivers side corner under the headlight Also notice my stamped tailgate ?
thread post photo


Cut the lip out to allow it to sit in proper spot,needs some sanding and welding now
thread post photo


Inner fender 1.5" thick(wires on outside):D
thread post photo


Before i cut the lip (2" to high)
thread post photo


Tubs back in ,the go to the inside of the frame (12.5" wide) Love it
thread post photo


Some camber haha
thread post photo


Chillin in the driveway
thread post photo

Bed needs cutting, grounds not 100% level
thread post photo

Bad picture of front max lift but it gets 10"
thread post photo
mazdadropped   +1y
for more pics - First four pages most recent
fitbmx180   +1y
slow progress, but it is a lot of work to accomplish...

you should sell me your bed.. i need a new one
mazdadropped   +1y
haha doubt it would happen but throw a price out there i just might do it and yes it takes a exremely long time
i plan on cutting off the front crossmember to lower it 2"
and cut out the passenger inner fender once i get it to its winter home ill be getting lots more done
jrock4224   +1y
Holy chit... i m sending you a bill for forty five minutes of my life back.....that truck is deystroyed...if your biggest concern is frenching in a mazda emblem to your firewall that CLEARLY WONT FIT....to begin with.... then its time to call pick a part and get your money out of the title...i am not gonna sugar coat anything here... dont sell it, you cant....its time to call the scraper....some of the questions you asked were real head scratchers...no thumbs up here .. itstime to call a person to save it or send it to the crushers....

what the hell happened the the rear clip...were u planning on laying out on tractor wheels..
jrock4224   +1y
wait u just said you plan on cutting of the front crossmeber and not replacing it or it does not sound like you plan on replacing it.....do you make most of your meals in a microwave... if so its time to take off the aluminum foil hat your wearing its causing damage...DO NOT REMOVE FRONT CROSSMEBER WIH OUT A PLAN TO PUT SOMETHING BACK IN...DO NOT