Page 1 of 2
Toyota Pickup Projects \ Thank you Mr.mailmanThank you Mr.mailman
views 2839
replies 14
following 4
oldsklminitrk
+1y
The manifold will be here Tuesday LC was dragging on that .......so when I get that in and the linkage Ill post all the part numbers so everyone can find the stuff online....or at a Napa or something
3tcrob
+1y
Ha I wish I could find Weber and Mikuni Linkage at Napa or even a manifold
Can't wait to see the manifold I'm intrested on the linkage set up and the throttle cable location
E-mail LC about it one time with nothing
Was wondering if it pulled from the center or from the outside of the rods
If you need a synch tool I have one if you want to borrow it
Ha I wish I could find Weber and Mikuni Linkage at Napa or even a manifold
Can't wait to see the manifold I'm intrested on the linkage set up and the throttle cable location
E-mail LC about it one time with nothing
Was wondering if it pulled from the center or from the outside of the rods
If you need a synch tool I have one if you want to borrow it
oldsklminitrk
+1y
Man I wish I knew that I already bought one.....I got all kinda manuals on these now so I can tune them......Lemme know I can hook ya up with a manual or tune them for you once I learn.
Its a cannon manifold I think and the linkage Ill get pics of it up and a tech set up of the install.....also I had to get a regulator cause Weber side drafts only like about 4psi not the 7 or 8 the factory pump puts out.Once I get it all in and good pics then that should tell the tale on how this is done.....I havent seen this done much and I dont think I have ever seen it done up close......btw these carbs came from a guy in NY....I paid 499.00 for both brand spankin new with everything you see....
Its a cannon manifold I think and the linkage Ill get pics of it up and a tech set up of the install.....also I had to get a regulator cause Weber side drafts only like about 4psi not the 7 or 8 the factory pump puts out.Once I get it all in and good pics then that should tell the tale on how this is done.....I havent seen this done much and I dont think I have ever seen it done up close......btw these carbs came from a guy in NY....I paid 499.00 for both brand spankin new with everything you see....
3tcrob
+1y
I had my 44s on my Toyota Corolla You can get one of the Facet pump that run about 3-5 psi and you will be fine I ran 2 1/2 psi on my Corolla with my .510 lift and it ran fine
Thanks on the manuels I have a Mikuni one here and Webers are way easier than Mikunis
Here is a pic of my Corolla
This is how it was before the massive rebuild going on now 45mm ITB's and a 5mm over block
Thanks on the manuels I have a Mikuni one here and Webers are way easier than Mikunis
Here is a pic of my Corolla
This is how it was before the massive rebuild going on now 45mm ITB's and a 5mm over block
3tcrob
+1y
It ran real good I have a ITG filter kit for them but you have to richen it up a couiple of points plus it slicenles them a little if you never had anything with sidedrafts you will never go back once you hear them suckins air you will be in love
I over reved this motr and flatened out the rod jornel on the rod but the bolts were still intact(ARP) and there was no sand or grit in the motor at all
I'm running a open carb now on my truck
I over reved this motr and flatened out the rod jornel on the rod but the bolts were still intact(ARP) and there was no sand or grit in the motor at all
I'm running a open carb now on my truck