anyone here also a member of mazdatruckin

I'm puzzled by this because when I ran a WhoIs on the domain name it looked to me like it was still K6. Here's one I just ran:

Domain name: mazdatruckin.com

Registrant Contact:
Kyrasis Productions
Kenneth Richards ()

Fax:
XXX XXXXXXXX Dr.
Apt # XXX
Columbia, SC 29210
US

Administrative Contact:
Kyrasis Productions
Kenneth Richards ()
+1.704XXXXXXX
Fax: 1.11
160 XXXXXX Ln
Statesville, NC 28625
US

Technical Contact:
Kyrasis Productions
Kenneth Richards ()
+1.704XXXXXXX
Fax: 1.11
160 XXXXXXX Ln
Statesville, NC 28625
US

Status: Locked

Name Servers:
dns1.name-services.com
dns2.name-services.com
dns3.name-services.com
dns4.name-services.com
dns5.name-services.com

Creation date: 13 Jan 2004 15:07:10
Expiration date: 13 Jan 2012 15:07:10


I added the X's so that K6 wouldn't have his name all over the internet, though anyone can get the information from WhoIs. Anyway, it doesn't look like a squatter at all - WhoIs says the same owner has had it since 2004 and that it just expired, with no change of owner.

Yup I got my flare wrenches, smile and all.

My question was "why can't I use a open ended wrench?" but then I googled it and found this tres amusing article + comments: Tool of the Week: Flare Nut Wrench and so I heeded that and got the Craftsman 9 pc. flare nut wrench set.

Now onto clutch cylinder replacement! It's getting so close....

I need to look around here and figure out what's what... I keep getting lost and confused about where I should be looking and posting. I know peeps were talking about the lay of the land a few pages back, I need to go back and read.

Good morning Lydia!

You can start a thread on your Clutch Master Cylinder replacement by clicking on the "Forums" tab at the top of the page, then scroll down to either "General Tech" or "Repair Tech" and start a thread in either one of those.

If you go to "Repair Tech" you can then pick a sub-forum to match what engine you have in your truck, but I think for something that really applies to all the 2nd gen. engines/trucks and doesn't have anything to do with the engine, I would just go with the "General Tech" forum heading.

Anyway, if ya start it in the wrong spot and later realize that, I'm sure one of the moderators can move the whole thread to the appropriate area.

Now go post that thread! <img src="{SMILIES_PATH}/icon_smile.gif" alt=":)" title="Smile" /><!-- s:) -->

PM'd

Lydia, My friend Earl here is right on spot!!!!! Post up!!! Also i am currently working on something to help with all of the sub-forums as it has been an issue for sometime as far as new members and getting lost without a map!!!







-Justin

Good for you!! I ALWAYS use the &quot;cost of the job&quot; excuse when it comes to getting more tools.

Post your questions on your clutch, I'm assuming it's the slave cylinder.

Don't sweat the initial confusion on this site, I had a similar experience. It happens when you go cold turkey.

Dan

Those sites are never legit thats why there FREE. That site is worth no were near $12k. I would say it would barely peak at 4 figures.

Thanks to all those welcoming us MazdaTruckin.com refugees. I'm looking forward to contributing and getting my fix.
Dan

WAAAHHH!!! I miss Mazdatruckin.... LOL

The different layout of this forum has me wondering where to place my project updates and annoyances...So..I end up thinking too long and forget about what I wanted to say. Then YouTube happens and I'm lost in there until I fall out of my computer chair asleep. It will take some getting used to. A change I hadn't wanted to do before, but may be forced to now.

I've been so down about it...I haven't touched or looked at or even smelled any of my Mazda's or Mazda parts for the past 2 weeks.

I'm interested with what Ken has been up to. He's been very quiet for a long time now on his forum. I hope everything gets sorted out...and I too would gladly contribute to help get the mazdatruckin board back up.

really? i think the layout is way easier then mt. its not broken down into 4 or 5 subcatagories, and the front page actually shows all updated threads. members projects is where youd put your updates or even just in general discussion. i love mbs layout.