ben shadys truck

I found somewhere to order some from but I've had some bacteria infection then pneumonia then I got tonsilitis... So needless to say the last week I haven't done shit. I'm just now back up and moving again. I gotta get a blueprint to send this guy so he knows exactly what I need then he said he's makes them for $4 each.

damn sorry bout your health luck but good to see back up on your feet and in tha garage

damn man sucks to get sick like that..

your not supposed to kiss them on the lips...hhaha

Sorry if i missed it but , what does the front end setup consist on this truck? Has it been Z'd, sectioned crossmember, spindles, 3/4t rotors, etc?

First time looking at this thread!!! All I can say is awesome fab work, and the truck looks killer also!!!!

Well my TH400 is about to shit out so I decided while I'm gonna have it out I might as well put the edelbrock intake on that i've had layin around.. soo I called lunati and ordered a cam kit then got on jegs and ordered a gear drive and gasket kit, a msd coil to go with my 6al. and then..... I called tbichips.com, gave him all my info and had him burn me a chip to fix my timing/fuel curves to work with all the mods. Sooo Now it'll finally run like a bbc and not dead in the water like it's been acting since the throttle body/header install.

I ordered some hinges from rocky hinges last week and they came in monday. I must say they are really nice. So if all works out I'll have the rear doors,motor and trans all done by slamily reunion. I've been doing some metal work inside my bed because I wasn't completely happy how the tubs were shorter than the factory inner fenders so there were some 2" pieces of flat sheet between the tubs and the ribs in the floor on both sides. So I built 12 new rib pieces and welded them all in and shaved my stake pockets while I was at it.

I'll get this damn thing lined out eventually. Even if I love driving it around with no bed on it. The brothers keep askin if dems 6's..... lol

glad to hear your still pluggin away at it....

which kit did you order from them i have been looking for a good one for my truck

60201 is the cam I got since I'm doing some computer work. If your gonna just use the stock stuff then they recomend the 60200.

Here's mine-
Part Number: LUN-60201
Cam Style: Hydraulic flat tappet
Basic Operating RPM Range: 1,000-5,500
Intake Duration at 050 inch Lift: 213
Exhaust Duration at 050 inch Lift: 219
Duration at 050 inch Lift: 213 int./219 exh.
Advertised Intake Duration: 256
Advertised Exhaust Duration: 262
Advertised Duration: 256 int./262 exh.
Intake Valve Lift with Factory Rocker Arm Ratio: 0.515 in.
Exhaust Valve Lift with Factory Rocker Arm Ratio: 0.530 in.
Valve Lift with Factory Rocker Arm Ratio: 0.515 int./0.530 exh. lift
Lobe Separation (degrees): 112
Intake Valve Lash: 0.000 in.
Exhaust Valve Lash: 0.000 in.

and here's the 60200

Part Number: LUN-60200
Cam Style: Hydraulic flat tappet
Basic Operating RPM Range: 1,000-5,000
Intake Duration at 050 inch Lift: 207
Exhaust Duration at 050 inch Lift: 213
Duration at 050 inch Lift: 207 int./213 exh.
Advertised Intake Duration: 250
Advertised Exhaust Duration: 256
Advertised Duration: 250 int./256 exh.
Intake Valve Lift with Factory Rocker Arm Ratio: 0.495 in.
Exhaust Valve Lift with Factory Rocker Arm Ratio: 0.515 in.
Valve Lift with Factory Rocker Arm Ratio: 0.495 int./0.515 exh. lift
Lobe Separation (degrees): 112
Intake Valve Lash: 0.000 in.
Exhaust Valve Lash: 0.000 in.