My Interior Project

looks sweet

lookin good man. im debating on doin tweed in mine fiberglass or a dash that i have out of my 51 chevy




-justin

I voted for the tweed, if anything whenever I wanna glass it later all I have to do is pull the tweed off and sand it back down.

I just updated the 720 thread, check it out. I'm stock flooring it, and I just finished the rails today. Might give you some ideas.

So I ordered more black tweed tuesday, it should be arriving monday morning. I had to order 2 yards more for my door panels.

I am undecided on what kind of design I wanna put into my doors, The casual flame is kinda played out to me no affense to anyone with it. It looks good but I just want something different.

How about some old school scallops?

hey man what kind of seats do you have in the 83? on solow93's post about his center console you said that you wanted to do something like that but with 12's. i have a bench seat and can't even find a spot to run a shallow sub in mine. i may run buckets just to get a little bump in her.

my seats are bucket s-10 seats outta a 94. I cut the original bracket off the floor for the factory seat. These seats sit very low I dig it.

Well I got some progress done and some parts.

So prepare to laugh, So as I go to lowes to by some wood to do my panels for my interior I buy the wood get outside and see that this shit will not fit into my hatch...........wtf. Can't wait to get rid of my piece of shit daily driver hint why I am getting a truck very soon. I open to hatch and the wood is about 4" to wide so I had no choice either leave the wood there go refund it and wait to use my stepdads truck for another 3 days so I said fuck that so I broke a piece off and shooved it in the car, It actually worked out good were I broke it so no worrys.




Just something simple nothing crazy, because not everyone is gonna see it and this is my first attempt at anything like this so oh well. This will be my trim panel piece that sits up against the back wall.


Scored a nice EDC from the junkyard for $30 with both brackets. This pump allows me to use my stock upper and lower a/c brackets. Sanden 708




Seen a guy on nissancustoms.com use these on his door panels and I thought it was a good idea, they work perfect and got a shit load for a $1.


Took this rear body line back down to bare sheetmetal as a used to be buddy of mine decided to slap bondo over them. What would that cause it to do? Cracking of course.
I am useing a little cheap $100 harbor freight welder, it blows well its okay. It gets the job done and Im going very very very slow so I dont warp this bed side. Its not complete in this pic.


This is a pic of it almost complete, I finished the last of it tonight.


Last but not least all my goody shit for the EDC. Most people don't run inline oilers on sandens but I figured what the hell it wouldn't hurt anything. Gotta love SMC and the prices.

Well I got some progress done and some parts.

So prepare to laugh, So as I go to lowes to by some wood to do my panels for my interior I buy the wood get outside and see that this shit will not fit into my hatch...........wtf. Can't wait to get rid of my piece of shit daily driver hint why I am getting a truck very soon. I open to hatch and the wood is about 4" to wide so I had no choice either leave the wood there go refund it and wait to use my stepdads truck for another 3 days so I said fuck that so I broke a piece off and shooved it in the car, It actually worked out good were I broke it so no worrys.




Just something simple nothing crazy, because not everyone is gonna see it and this is my first attempt at anything like this so oh well. This will be my trim panel piece that sits up against the back wall.


Scored a nice EDC from the junkyard for $30 with both brackets. This pump allows me to use my stock upper and lower a/c brackets. Sanden 708




Seen a guy on nissancustoms.com use these on his door panels and I thought it was a good idea, they work perfect and got a shit load for a $1.


Took this rear body line back down to bare sheetmetal as a used to be buddy of mine decided to slap bondo over them. What would that cause it to do? Cracking of course.
I am useing a little cheap $100 harbor freight welder, it blows well its okay. It gets the job done and Im going very very very slow so I dont warp this bed side. Its not complete in this pic.


This is a pic of it almost complete, I finished the last of it tonight.


Last but not least all my goody shit for the EDC. Most people don't run inline oilers on sandens but I figured what the hell it wouldn't hurt anything. Gotta love SMC and the prices.