AIM/Chassis Tech Discussion - Get Help

Originally posted by bgp1mpin



this isn't constructive and i know it i have made my case previously no results could satisfy me because the case has been over with so long there is no way to make it right that being said my only other complaint is the fact that you called everyone that posts in these forums a liar in a major publication. without checking any facts you said we were making it all up for fun. thats the same as callin me a liar to my face on a commercial during halftime at the superbowl. maybe its just me but is kinda rubs me the wrong way and while you have apologized for stuff here but it seems like a retraction in those publications would really set the record straight. just my two pennies and with that i no longer wish to discuss the subject. good luck to all parties i hope everything goes well for all of you. THE END

kelly

THE ENDYour email makes no sense to me, can you be so kind as to post the facts or the quote. I am talking about your "liar" accusation.

If you can show me a majority of members that do not want me to make things right, then please list them, because they have no issue other that to just dump on me. I will continue to assume that the majority of the members WANT TO SEE IMPROVEMENT. And that is just what this is about.

Thank you also for your post. It allows members to decide for themselves if I am good or bad for the forum. Now, do you have a REAL issue that you need help with for the betterment of the community? If so, please post it and lets take a step forward.

Originally posted by AfterHoursEst2001



I was very happy with my Mighty Max spindles from AIM..no complaints here.

Thank you! I finally did something right today....

Sincerely

Originally posted by bmoxley



joe, i bought come control arms uppers and lowers ive only had them for about 2 mth. and the cross shafts and in some spots the powder coating has come off and the have rusted not major rust,is their any thang that i could do 2 fix the problem i know that i couls sand the down and repaint the but lioke i said ive had them for about 2 mth

bmoxley,I know it is not practical to send them back for bead blasting and re-powdercoat. We will continue to work on producing a higher standard of powdercoat. Short of plating, it is a difficult thing to address.

Thank you for the posting,

Originally posted by nautiquess



Joe, That was my post, and it got deleted when they cleaned it up. I hope you didn't take it the wrong way, I was just stating that it was great that you are here and clearing things up, I was ranting that I felt it was turning into a different thread than it started and was veering off path, but the Moderators cleared it up just in time. Thank you.

BTW, did you recieve my last couple emails?

-Thanks, Chad AndersonChad,I have one unaswered email from you, I will open it now. Difficult for me to be everywhere, but I am trying....

ps sorry about the bad punctuation it does read kinda crazy. i posted earlier about a problem i had and you offered me a credit that i didnt want because i am through with aim. the part where you called all the people who post in the forums liars (in not so many words) in your ad in the magazines i took quite a bit of offense to. all i was trying to say was an apology in your ads in the magazine would go a long way toward proving your sincerity hopefully that is a bit more clear. and that is all i have to say about that. again i hope this works ouy well for all parties involved. the end (for real this time)

kelly

I stopped by AIM today at 4:25pm to check on some parts and found the big red gate to be closed but didnt see a sign ANYWHERE with hours of operation posted

are there certain hours the AIM showroom is open ?

Originally posted by BOOOGHAR



I stopped by AIM today at 4:25pm to check on some parts and found the big red gate to be closed but didnt see a sign ANYWHERE with hours of operation posted

are there certain hours the AIM showroom is open ?Sorry, showroom closes at 4:30 and the phones are live until 5:30PM. Call on your cell next time, and someone will come out.

tx

Originally posted by bgp1mpin



ps sorry about the bad punctuation it does read kinda crazy. i posted earlier about a problem i had and you offered me a credit that i didnt want because i am through with aim. the part where you called all the people who post in the forums liars (in not so many words) in your ad in the magazines i took quite a bit of offense to. all i was trying to say was an apology in your ads in the magazine would go a long way toward proving your sincerity hopefully that is a bit more clear. and that is all i have to say about that. again i hope this works ouy well for all parties involved. the end (for real this time)

kellyMany people interpret the same thing in many ways. If you are looking for fault, I guarantee you will always find it.Take care

It appears that the following post did not show up, so here it is:

FROM OUR AIM CUSTOMER:
Hello joemorrow

You have received a reply to your posting on the StreetSourceMag.com Forum.Regarding the subject - AIM/Chassis Tech Discussion - Get Help.


New Message:
I got my spindles today, just like I was told I was. Not even 24 hours has past since I was told they were shipped. Thanks Joe, and Yuri..

You can view the reply at http://www.streetsourcemag.com/forum/topic.aspx?whichpage=21&topic_id=105491&forum_id=13

Thank you

I am done for the evening. Good Night and back on it in the morning